Page 1 of 2
Rust bubbles
Posted: Mon Jul 16, 2007 5:10 pm
by chitwnvw
I had some bubbles in my paint that I took a wire brush to, only to discover I had some pin holes. This is in the area between the back of the sliding door and the passenger side rear wheel well. What causes conditions favorable for rust here? It comes from the inside, and I don't want to patch and hope for the best.
Posted: Mon Jul 16, 2007 7:41 pm
by Ryno
Sounds like a leaky window seal or slider door seal. Isolate the leak with the ol' garden hose and fix that first.
Posted: Tue Jul 17, 2007 8:14 am
by chitwnvw
[albumimg]1077[/albumimg]
Finally got around to taking a picture. I'm not sure that the water's coming in through the window seal, I think that area is it's own isolated area. It's weird too that it bubbles up there and doesn't start at the bottom. There is some metal behind the pinholes, which makes me think there's something structural in there that's trapping water and debris. But my drain hole is open and I can't figure out where the bad stuff is getting in at...unless it's coming up through the drain hole.
Posted: Tue Jul 17, 2007 8:39 am
by Ryno
chitwnvw wrote:
Finally got around to taking a picture. I'm not sure that the water's coming in through the window seal, I think that area is it's own isolated area. It's weird too that it bubbles up there and doesn't start at the bottom. There is some metal behind the pinholes, which makes me think there's something structural in there that's trapping water and debris. But my drain hole is open and I can't figure out where the bad stuff is getting in at...unless it's coming up through the drain hole.
That area may have been repaired once or twice already, so who know's what's in there. Did you have your interior panels out along that wall at some time?
Posted: Tue Jul 17, 2007 9:11 am
by chitwnvw
Yah, it's behind the Westy cabinet, the one with the full size mirrored door, but that area is below the floor line, so I can't get at it from behind.
Posted: Tue Jul 17, 2007 9:29 am
by Ryno
With the cabinet along that wall, it's difficult to tell if the window seal is leaking. Stick your head in the cabinet and have someone spray that baby down really good, I would bet you'll see a leak there. Sometimes they will only leak in really heavy rain, my old westy had that problem.
Posted: Sat Jul 21, 2007 7:56 pm
by chitwnvw
I was working on this area again today. The rust bubbles are lined up with the floor, soooooooo....I think you're right, water must come in through the window, drain down to where the floor is joined to the outer wall.
Anyway, I've got a seal for that window coming. Unfortunately, I'll have to remove the Westy stuff to do the job. Them’s the breaks. It'll be interesting to see what I find.
Posted: Sun Jul 22, 2007 5:29 am
by Ryno
Chitwn,
One area to pay close attention to is the bottom back corner of the window. That area seems prone to rust holes.
Posted: Thu Apr 24, 2008 7:51 am
by chitwnvw
Well Turk and I pulled what I thought was the offending window and all we found was some surface rust, not one hole! Any ideas on where else water could access this area?
[albumimg]1077[/albumimg]
Posted: Thu Apr 24, 2008 9:41 pm
by Amskeptic
chitwnvw wrote:Well Turk and I pulled what I thought was the offending window and all we found was some surface rust, not one hole! Any ideas on where else water could access this area?
There doesn't have to be a hole in the window channel for water to get in and rust out your car. It can easily wick over the pinchweld from dribbles down the vertical runs. Also, check carefully the seatbelt anchors at the right rear wheel well. It does not matter if the seatbelts are not installed in that position, the bolt hole may be breached. While in the wheel well, look at the access plugs along the inner fender line where the factory injected wax between the outer fender and the inner fender.and really check under any undercoating for breaches. Most of these annoying rust throughs are at sandwiched panels. You must aggressively seek the water incursions. You can have a dry interior down to the floor, a nice wheel well behind the rust area and yet you are taking in water between the welded panels from behind the sliding cover at the catch, for all you know. This can be devilishly irritating to fully track down, but you will know how the vehicle is constructed a lot better by the time you are done.
Colin
Posted: Thu Apr 24, 2008 9:49 pm
by chitwnvw
Thanks for the feedback. Thanks for changing you avatar! That last one was giving me nightmares.
Since that last pic, I've grinded it down and sprayed the heck out of it with rust converting primer and gempler's version of WaxOyl pumped into the chamber. I primered it and 10 months later, there's no more corrosion.
Posted: Sun Apr 27, 2008 8:50 pm
by chitwnvw
More inspection.
Inside, the panel, behind the sliding door, where the floor meets the outer skin.
(Click on the pics for the full story)
[albumimg]1954[/albumimg]
[albumimg]1955[/albumimg]
Doesn't look too bad, although the camera picks up more than the eye does.
I decided to start removing some of the seam sealing caulk, it's a very tight space, a real pita!:
[albumimg]1960[/albumimg]
Why is there so much room 'tween the outer skin and the floor lap joint.
[albumimg]1961[/albumimg]
Smoking gun.
So there weren't any obvious signs of rust on the inside. But near the sliding door, there was a gap in the seam sealer caulk, the water got in...somehow... and wicked along the seam.
I will wait now for a heavy rain to make sure the new window seal has fixed the water leak problem.
Then wait a couple of days for the weather to warm up so I can spray the heck out of the existing rust with converting primer.
It's a weird space. There's a drain hole, but I don't know where they thought water was going to enter, so why the drain?
Posted: Sun Apr 27, 2008 8:55 pm
by Amskeptic
chitwnvw wrote:There's a drain hole, but I don't know where they thought water was going to enter, so why the drain?
Water can enter just from heavy condensation from nine passengers breathing on a humid day. Breathing. Yuck. Water can enter through the long through bolt that goes through the belt line. I don't remember a drain hole in that space.
Colin
Posted: Sun Apr 27, 2008 9:22 pm
by chitwnvw
This is my understanding of the area:
[albumimg]1963[/albumimg]
By the severity of rust damage, I can tell it started from the sliding door side and worked it's way back
I have the interior out now. I will protect this area and keep an eye to see if moisture is entering during rain, etc.
Posted: Mon Apr 28, 2008 7:24 am
by hambone
You're a brave man, that's a lot of work.