Here are a couple shots of the collars I tig welded where they were leaking. The #2 had the largest crack. 3-4 side did not appear to have any cracks that were noticeable via sight or sound but I tig welded them anyhow.
Now sanding and prepping for heat temp paint.
Tig Weld T4 Exhaust Flange Collars
-
- Old School!
- Location: Seattle, WA./HB. Ca./Shizuoka, Japan
- Status: Offline
Tig Weld T4 Exhaust Flange Collars
1972 Westy tintop
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
-
- Old School!
- Location: Seattle, WA./HB. Ca./Shizuoka, Japan
- Status: Offline
Re: Tig Weld T4 Exhaust Flange Collars
#4 side
1972 Westy tintop
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
-
- Old School!
- Location: Seattle, WA./HB. Ca./Shizuoka, Japan
- Status: Offline
Re: Tig Weld T4 Exhaust Flange Collars
#3 collar
1972 Westy tintop
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
-
- Old School!
- Location: Seattle, WA./HB. Ca./Shizuoka, Japan
- Status: Offline
Re: Tig Weld T4 Exhaust Flange Collars
All back together and the bus runs and sounds great. Replaced all the exhaust copper rings and gaskets. Annealed the rings prior to install and used Loctite 518 as well. I'm running an S&S 4-1 header so I applied a very thin coat of Hi-temp copper on both sides of the flange gaskets to add to sealing ability/durability.
Also sanded and repainted the heater boxes using VHT hi-temp paint.
Also sanded and repainted the heater boxes using VHT hi-temp paint.
1972 Westy tintop
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
- Amskeptic
- IAC "Help Desk"
- Status: Offline
Re: Tig Weld T4 Exhaust Flange Collars
Where were you when the #2 flange released itself from the pipe on my junky Dansk exchanger on the Road Warrior? Could have saved me the 300 big ones for a new exchanger.72Hardtop wrote:All back together and the bus runs and sounds great. Replaced all the exhaust copper rings and gaskets. Annealed the rings prior to install and used Loctite 518 as well. I'm running an S&S 4-1 header so I applied a very thin coat of Hi-temp copper on both sides of the flange gaskets to add to sealing ability/durability.
Also sanded and repainted the heater boxes using VHT hi-temp paint.
Do you find that welding projects just pop up now that you have a tig welder?
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
-
- Old School!
- Location: Seattle, WA./HB. Ca./Shizuoka, Japan
- Status: Offline
Re: Tig Weld T4 Exhaust Flange Collars
I used my friends welder. He doesn't have much experience welding those types of material together. It isn't particularly easy for a novice. Those pipes when originally brazed actually sit down in the collar a bit. Getting to it is a bit of a pain. It's really a matter of filling in the crack and then building outward from it. The 3-4 side wasn't leaking but I went ahead and welded them anyhow. Difficult spot to make a beautiful weld but in the end it will hold well.
1972 Westy tintop
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's
2056cc T-4 - 7.8:1 CR
Weber 40mm Duals - 47.5idles, 125mains, F11 tubes, 190 Air corr., 28mm Vents
96mm AA Biral P/C's w/Hastings rings
42x36mm Heads (AMC- Headflow Masters) w/Porsche swivel adjusters
71mm Stroke
Web Cam 73 w/matched Web lifters
S&S 4-1 exhaust w/Walker 17862 quiet-pack
Pertronix SVDA w/Pertronix module & Flamethrower 40K coil (7* initial 28* total @3200+)
NGK BP6ET plugs
002 3 rib trans
Hankook 185R14's