Why Does My 34 PICT 3 Flood After Shutdown?
- hambone
- Post-Industrial Non-Secular Mennonite
- Location: Portland, Ore.
- Status: Offline
You might want to check the pressure again, I had the same problem but shims fixed it.
Maybe you just need to get that tired ol' carb rebuilt by Keith.
Maybe you just need to get that tired ol' carb rebuilt by Keith.
http://greencascadia.blogspot.com
http://pdxvolksfolks.blogspot.com
it balances on your head just like a mattress balances on a bottle of wine
your brand new leopard skin pillbox hat
http://pdxvolksfolks.blogspot.com
it balances on your head just like a mattress balances on a bottle of wine
your brand new leopard skin pillbox hat
- vwlover77
- IAC Addict!
- Location: North Canton, Ohio
- Status: Offline
It was 80 degrees here today so I got the Beetle out for a top-down ride. Got it good and warm and when I got home and shut it off, I immediately clamped the fuel line between the pump and carb.
No difference. After half an hour or so, I pulled off the air cleaner and looked down the throat to see the throttle plate soaking wet with gas. The end of the throttle shaft had drops on them too.
Maybe a carb rebuild with a new top gasket is the best place to start?
No difference. After half an hour or so, I pulled off the air cleaner and looked down the throat to see the throttle plate soaking wet with gas. The end of the throttle shaft had drops on them too.
Maybe a carb rebuild with a new top gasket is the best place to start?
Don
---------------------------
78 Westy
71 Super Beetle Convertible Autostick
"When we let our compassion go, we let go of whatever claim we have to the divine." - Bruce Springsteen
---------------------------
78 Westy
71 Super Beetle Convertible Autostick
"When we let our compassion go, we let go of whatever claim we have to the divine." - Bruce Springsteen
- Amskeptic
- IAC "Help Desk"
- Status: Offline
Take the fuel line off to verify that you have stopped the fuel flow. . . . carefully with a hot engine. Free the fuel line from the carb then stick it back on in the morning while the engine is cool so you have a better time of it when it is warm. Clamping it may not be sufficient.vwlover77 wrote:It was 80 degrees here today so I got the Beetle out for a top-down ride. Got it good and warm and when I got home and shut it off, I immediately clamped the fuel line between the pump and carb.
No difference. After half an hour or so, I pulled off the air cleaner and looked down the throat to see the throttle plate soaking wet with gas. The end of the throttle shaft had drops on them too.
Maybe a carb rebuild with a new top gasket is the best place to start?
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
- spiffy
- IAC Addict!
- Location: Walla Walla, WA
- Status: Offline
I would take the carb off (two bolts and two screws) empty it out and check the thang (sorry, don' t know the technical term) at the bottom of the bowl....that thing can leak. Either way get a quality rebuild kit for $40 and get all the carb internals to YOUR standard. If you "rebuild" it and you still run into problems despite due diligence then look at the TS bushings. A single carb is THE simplest form of induction, figuring out the "voodoo" is fairly simple as the problem can only exist in an object smaller then a pint of beer.
78 Riviera "Spiffy"
67 Riviera "Bill"
67 Riviera "Bill"
-
- IAC Addict!
- Status: Offline
On the top of the carb body, under the top that is removable to get at the float bowl, are a couple of holes where the gasket sits. They may be plugged up or the wrong gasket may have been used and is covering them. I believe they are vents for the carb. when you shut it off the gas expands from the heat rising off the engine and has nowhere to go. So it pushes out through the accelerator pump and down the throat.
This is a guess but worth popping the top off and looking.
This is a guess but worth popping the top off and looking.
1/20/2013 end of an error
never owned a gun. have fired a few.
never owned a gun. have fired a few.
- Amskeptic
- IAC "Help Desk"
- Status: Offline
There is a diagonal tube right next to the choke plate that goes to the ceiling of the float chamber. That that tube is the "vent."vdubyah73 wrote:On the top of the carb body, under the top that is removable to get at the float bowl, are a couple of holes where the gasket sits. They may be plugged up or the wrong gasket may have been used and is covering them. I believe they are vents for the carb. when you shut it off the gas expands from the heat rising off the engine and has nowhere to go. So it pushes out through the accelerator pump and down the throat.
This is a guess but worth popping the top off and looking.
Bentley is pretty stubborn about difficult hot starts, "it's the needle valve" they say. They are silent about the benefits of the anti-percolation valve on the fuel pumps of the later carbureted Volkswagens.
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
- Amskeptic
- IAC "Help Desk"
- Status: Offline
This punky summer so far has not given me an opportunity to really test the fuel pressure regulator as a hot-start improvement device, but so far it has done just that. 93* in Portland over the past couple of days and the bus started just fine. I will let you y'all know how it does if I can get down into the deserts over the next couple of weeks before they cool too much below 115*
Colin
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
- vwlover77
- IAC Addict!
- Location: North Canton, Ohio
- Status: Offline
Well, it's been a while, but here's an update. I had the carb bushings replaced by Krusty Karb Keith, cleaned all carb passages and jets, cleaned and checked the needle valve (it's fine), and installed an adjustable fuel pressure regulator in the fuel line between the pump and the carb (as close to the carb inlet as I could get it.)
With the pressure set to 1/2 PSI (as low as it will go), the engine runs fine, but the carb still floods during the heat-soak after shutdown. The only good news is that fuel no longer drips from the ends of the throttle shaft thanks to the new bushings.
I'm thinking of installing an electric fuel cutoff valve in the inlet line to the carb. Here's my reasoning: The fuel that is emptied out of the bowl during the heat-soak will cause the float to drop, allowing more fuel under residual pressure to refill the bowl, providing more fuel to "boil over" into the carb throat. With a cutoff valve, at least the flood will be limited to only the fuel in the bowl at shut down.
I'm thinking of one like this:
http://www.dan-marcrvparts.com/12vomufushof.html
With the pressure set to 1/2 PSI (as low as it will go), the engine runs fine, but the carb still floods during the heat-soak after shutdown. The only good news is that fuel no longer drips from the ends of the throttle shaft thanks to the new bushings.
I'm thinking of installing an electric fuel cutoff valve in the inlet line to the carb. Here's my reasoning: The fuel that is emptied out of the bowl during the heat-soak will cause the float to drop, allowing more fuel under residual pressure to refill the bowl, providing more fuel to "boil over" into the carb throat. With a cutoff valve, at least the flood will be limited to only the fuel in the bowl at shut down.
I'm thinking of one like this:
http://www.dan-marcrvparts.com/12vomufushof.html
Don
---------------------------
78 Westy
71 Super Beetle Convertible Autostick
"When we let our compassion go, we let go of whatever claim we have to the divine." - Bruce Springsteen
---------------------------
78 Westy
71 Super Beetle Convertible Autostick
"When we let our compassion go, we let go of whatever claim we have to the divine." - Bruce Springsteen
- Amskeptic
- IAC "Help Desk"
- Status: Offline
My chromy deal on the Road Warrior actually helped prevent heat-induced percolation. Your float level was good?vwlover77 wrote:With the pressure set to 1/2 PSI (as low as it will go), the engine runs fine, but the carb still floods during the heat-soak after shutdown.
With a cutoff valve, at least the flood will be limited to only the fuel in the bowl at shut down.
I will be interested to know how the shut off works. Sounds good in theory.
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
- Hippie
- IAC Addict!
- Location: 41º 35' 27" N, 93º 37' 15" W
- Status: Offline
- vwlover77
- IAC Addict!
- Location: North Canton, Ohio
- Status: Offline
-
- IAC Addict!
- Status: Offline
clothes pins are an old skool jury rig for vapor lock, as well as tin foil wrapped around the fuel line. Helps dissipate the heat.
Vapor lock is when the fuel boils in the line before the pump. The pump can't pump vapor very well and the bowl runs dry. If you have a dirty filter BEFORE the pump you will be more prone to vapor lock, as the pump is sucking harder to overcome the blockage creating lower pressure in the supply line. Lower pressure makes the gas boil at a lower temp.
Vapor lock is when the fuel boils in the line before the pump. The pump can't pump vapor very well and the bowl runs dry. If you have a dirty filter BEFORE the pump you will be more prone to vapor lock, as the pump is sucking harder to overcome the blockage creating lower pressure in the supply line. Lower pressure makes the gas boil at a lower temp.
1/20/2013 end of an error
never owned a gun. have fired a few.
never owned a gun. have fired a few.
- themarshotel7
- I'm New!
- Location: Valparaiso Indiana
- Status: Offline
Re: Why Does My 34 PICT 3 Flood After Shutdown?
Ok, I'm having the exact same problem with my 71 stock westy. Mine does not have to be hot to do it though, i can drive around the block when it's stone cold and after i shut it off, it slowly begins to drip. after several hours, it stops dripping. I even removed the top of the carb and it still drips from the throttle shaft. It's beginning to drive me crazy! It did not start doing this until after sitting for the winter. Please give me some idea's.
Ok, big update. I pulled the carb again cleaned it up and set it on the bench with the top off. I then put fuel in the carb and here's what I found.
Fuel slowly begins to seep out of the little pinholes (not sure what thier called) in the carb throat. Then running along the throttle plate and eventually out of the throttle shaft. Im guessing those are fed from the jet in the bowl through the emulsion tube?? Any thoughts?
Ok, big update. I pulled the carb again cleaned it up and set it on the bench with the top off. I then put fuel in the carb and here's what I found.
Fuel slowly begins to seep out of the little pinholes (not sure what thier called) in the carb throat. Then running along the throttle plate and eventually out of the throttle shaft. Im guessing those are fed from the jet in the bowl through the emulsion tube?? Any thoughts?
1971 westfalia
1972 super beetle
1991 Fox
2001 eurovan
1972 super beetle
1991 Fox
2001 eurovan
- Amskeptic
- IAC "Help Desk"
- Status: Offline
Re: Why Does My 34 PICT 3 Flood After Shutdown?
High float level or inadequate needle valve. Those are my thoughts.themarshotel7 wrote:Ok, I'm having the exact same problem with my 71 stock westy. Mine does not have to be hot to do it though, i can drive around the block when it's stone cold and after i shut it off, it slowly begins to drip. after several hours, it stops dripping. I even removed the top of the carb and it still drips from the throttle shaft. It's beginning to drive me crazy! It did not start doing this until after sitting for the winter. Please give me some idea's.
Ok, big update. I pulled the carb again cleaned it up and set it on the bench with the top off. I then put fuel in the carb and here's what I found.
Fuel slowly begins to seep out of the little pinholes (not sure what thier called) in the carb throat. Then running along the throttle plate and eventually out of the throttle shaft. Im guessing those are fed from the jet in the bowl through the emulsion tube?? Any thoughts?
Colin
BobD - 78 Bus . . . 112,730 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles
Chloe - 70 bus . . . 217,593 miles
Naranja - 77 Westy . . . 142,970 miles
Pluck - 1973 Squareback . . . . . . 55,600 miles
Alexus - 91 Lexus LS400 . . . 96,675 miles